Re: Random/Sequential measurement on Filers
Hi Jeremy, Thanks for the reply. Excuse my ignorance here but I looked at the disk statistics from statit and it I can't see how I can determine the
View ArticleRe: Random/Sequential measurement on Filers
Statit will get you the AMALGAMATED workload to disks on writes, not individual IOs. There's nothing there. On reads..sure, I can see that. The un
View ArticleRe: Random/Sequential measurement on Filers
I am not sure that's really true. ALL writes are going to be "sequential" if they can - the filer writes to NVRAM not disk directly. So the AFAIK the
View ArticleRe: Random/Sequential measurement on Filers
:s/NVRAM/System Memory/g Fixed it for ya. :) On Thu, Jan 16, 2014 at 2:01 PM, Jeremy Page <jeremy.page@gilbarco.com>wrote: > I am not sure tha
View ArticleRE: AW: Consistency Point Type M
Did you guys ever figure out what was causing these/correct this issue. I am seeing what sounds like the same thing on a 3240 , however.. When I
View ArticleRe: AW: Consistency Point Type M
Does it need corrected? Sent from my iPhone > On Jan 17, 2014, at 1:51 PM, Jordan Slingerland <Jordan.Slingerland@independenthealth.com> wrote: > >
View ArticleAW: AW: Consistency Point Type M
Hi Jordan, no, since we talked with the customer and he said he was doing unusual workloads which he usually does not run on this system and it als
View Articlereallocate effect on snapmirror and snapvault
Hi, I'm thinking of running a "reallocate start -p" on a couple volumes that are showing high latency disk accesses for luns. The volume is a sour
View ArticleRe: reallocate effect on snapmirror and snapvault
rrhodes@firstenergycorp.com wrote: > I'm thinking of running a 'reallocate start -p' on a couple volumes that > are showing high latency disk accesse
View ArticleRE: 2240 hot add tray
Here is the link to the netapp support site doc for hot adding the shelves. https://library.netapp.com/ecm/ecm_download_file/ECMP1119629 Thank you
View ArticleRe: 2240 hot add tray
You are going to disable one path. Hook it up. Re-enable the path. Disable the other Path. Hook up the second path. Re-enable the second path. If App
View ArticleRe: 2240 hot add tray
thanks Will, for the direct link ! On Jan 20, 2014, at 2:38 PM, "William Atherton" <watherton@BERKCOM.com> wrote: > Here is the link to the netapp
View ArticleRE: 2240 hot add tray
probably some overlap in info, but there is a sas and apc cabling guide as well. https://library.netapp.com/ecm/ecm_get_file/ECMM1280392 ____________
View ArticleRE: 2240 hot add tray
The Netapp doc mentioned is pretty good. I also use the Netapp Config Advisor tool http://support.netapp.com/NOW/download/tools/config_advisor/ y
View ArticleRe: Random/Sequential measurement on Filers
Isn't NVRAM slower than system RAM? So in theory could cause a bottleneck (this may no longer be true but you don't also have to wait for a CP on syst
View ArticleC-mode & ARP cache...
Does anyone know if a C-mode filer does a gratuitous ARP when it fails a port over? Got a VM issue I'm trying to resolve. Mark Flint mf1@sanger.ac.
View ArticleRe: Random/Sequential measurement on Filers
"Isn't NVRAM slower than system RAM?" --- The access to/from/etc, sure. LIkely. Probly. "So in theory could cause a bottleneck" --- Not unless your
View ArticleRE: C-mode & ARP cache...
Yes. We pretty much have to since all LIFs on a port use the same MAC address. Technically, we don't fail ports over - we fail over the logical inte
View ArticleRe: Random/Sequential measurement on Filers
On Jan 21, 2014, at 10:07 AM, Jeff Mohler <speedtoys.racing@gmail.com> wrote: > ..which is why if you wanna go faster, blame the network team. :) :
View Articleflow control and 10g interfaces - ifgrps and vlans
Can flow control be disabled on a vlan interface? I tried in a simulator and It spits back "SIOCSFLOWCONTROL - Operation not supported by device" In
View Article